Best Body For Ball Valve

DAN SPEED 1.5 NPT Female Threaded Full Port Ball Valve with Blue Vinyl Lever Handle,316 Stainless Steel,WOG1000

Body & Ball Type:Full Port, Low Operation Torque,Temp Range:-60F to 450F.
The valve is fitted with PTFE seals for maximizing corrosion resistance and lifespan of the ball valve.
This ball valve is made of Stainless Steel 316 and has a plastic-covered lever handle for on/off manual control.
Nominal Working Pressure:1000 WOG:Max 1000 psi for Water, Oil, Gas. Fluid Medium:For use with liquids and gases.
This inline valve has a Standard port flow and 1.5" female National Pipe Taper (NPT) threads for connecting two male threaded pipe fittings going in....

Material: the body of the body is made of quality ABS plastic material, which is featured with good heat resistance and impact resistance of PC resin, not corrode or rust. The float is made of PE material with nice stability. The valve core is made of silicone material which is non-toxic and odorless, safe for you to use..
Easy to use: you can have a automatic water level control by adjusting the angle which is formed by the float and the valve body, if the surface of water contacts the float, the water inlet switch will be automatically closed..
Quantity and measurement: we provide you with a total of 4 pieces 1/ 2 inch float ball valves, the valve total length is approx. 7.87 inch and a float length is about 3.74 inch, you can install different numbers of the water valves according to the size of the tank or pool..
Suitable condition: the float ball valve can be adapted to water temperature which ranges from 0 to 70 degrees Celsius, 0.01-0.8MPA water pressure is applicable, featuring with good control of the water inlet, will give a nice using experience to you..
Multifunction: our plastic water filter float ball valves are suitable for a variety of occasions, such as small swimming pools and storage tanks at home, more numbers of water valves should b....

Attention: Inside Access Needed to Install the Nut.
Stainless Steel 304 Body w/ Aluminum Alloy Handle. No Lead, Corrosion Resistant..
Stainless Steel Quarter Turn Ball Valve, Turn Right to close..
For all ball valve, there is a chamber around the ball may trap water. May contain water from testing, which is normal..
Fit up to 1/4 inch thickness wall, 10 mm water flow opening, With Garden Hose Hook up. Need 21mm or 7/8 inch hole saw to install..

PACKAGE INCLUDED: You will receive 2 pieces water float ball valves and 1 roll plumber's tape..
PRINCIPLE of OPERATION: The float valve could control the flow rate and opening and closing of the inlet pipe through the floating of the ball. When the water level rises to a certain level, the water injection will be cut off.
when the water level drops to a certain limit, the water is automatically injected..
APPLICATION: The float valve is suitable for water storage tanks, pools, aquariums, fish tanks, livestock sinks, aquaculture, etc. 1/2" male thread inlet, suitable for most types of water pipes, easy to install and adjust..
HIGH QUALITY MATERIAL: The arm and connector of water float ball valve is made from high quality brass and the float ball body is made from plastic..
AFTER-SALES SERVICE: The float ball valve can only work properly if the water pressure is appropriate. We promise to provide every customers with satisfying shopping experience. If you come across any issues during use our products, please feel free to contact us..

EZ-FLO SCHEDULE 40 PVC BALL VALVE: This EZ-FLO ball valve is suitable for use as an inline valve for connecting two pipes going in the same direction.
equipped with a 3/4 inch slip connection on each end.
DURABLE: This schedule 40 PVC ball valve is made of heavy-duty CPVC that protects against corrosion and provides strength and durability.
EASY TO USE: This PVC ball valve is equipped with a quarter-turn red plastic handle for an easy-to-control water flow.
SPECS: This valve can withstand a working pressure of 150 PSI and a maximum temperature of 140 degrees F.
SAFETY: This ball valve complies with lead-free guidelines for potable water applications.

SAFE AND RELIABLE- The valve body is made of SS304 steel, with NSF certification, this ball valve is safe for drinking water.
NPT THREADING- ½" Stainless steel threading, manufactured and measured according to National Pipe Thread standards.
9V-24V AC/DC- Works effectively over entire voltage range.
No power expended once fully open or fully closed.
3 WIRE, 2 POINT CONTROL SETUP- Simple three wire connection, with two points of control.
ALTERNATIVE TO SOLENOID VALVES- Automatically cuts off power once fully open or fully closed.
This reduces likelihood of overheating, making it a....

Reduced pressure principle backﬂow preventer consisting of a pressure differential relief valve located between twoindependently operated spring-loaded center guided check valves, “Y” pattern body.
Complete with two full port resilient seated ball valves for shut-off and four resilient seated ball valve test cocks.
Pre-plumbed backﬂow station. Assembly can be of the reduced pressure principle or of the double check type.

This 3/4 in. double check valve assembly is designed to prevent the backflow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure in accordance with national plumbing codes and water authority requirements..
Its compact modular design facilitates easy maintenance with a single access cover for in-line repairs..
The FEBCO Series 850 Double Check Valve Assemblies are designed for non-health hazard applications..
This assembly consists of a bronze body construction, NPT end connections, quarter turn ball valve shutoffs, top mounted test cocks, 2 in-line independent positive seating check modules, captured springs, and replaceable check discs and seats..
Bronze body for durability, Modular compact design, Replaceable seats and seat discs, Top entry.

【100% No-risk Purchase】If you receive any problems with pressure washer ball valve, you can get a full refund or a new one for free! Please feel free to contact us if you have questions during use. We will give you a satisfactory answer within 12 hours. Customer satisfaction is our tireless pursuit..
【Convenience and Safety】Ball valve for pressure washer gun is made of lightweight material, 3/8" Female BSP Inlet x 3/8" Female BSP Outlet with round frame. DN10 ball valve unique design can withstand high Pressure can be used for pressure washer gun, foam cannons and power washer..
【Solid Structure】The power washer shut off valve is made of high quality plated brass for compactness, ruggedness, and enhanced rust and corrosion resistance for long-term worry-free use. The high pressure ball valve can reach a maximum working pressure of 3000 PSI and a maximum working temperature of 176 degrees Fahrenheit..
【Leakproof Performance】Power wash ball valve with excellent PTFE (Polytetrafluoroethylene) seals provide perfect leakage protection and improves performance through high heat and chemicals. No need to ....