Best Board Connector

SparkFun MicroMod LoRa Function Board - 1W 915M30S LoRa Module Frequency Range: 900 - 931MHz Transmit Power 28.5 - 30dBm (max) Modulation LoRa, FSK, GFSK, MSK, GMSK, OOK Antenna Impedance: 50Ω

The 1W LoRa MicroMod Function Board adds LoRa capabilities to your MicroMod project. It is intended to be used in conjunction with a MicroMod processor board and a MicroMod main board, which provides the electrical interface between a processor board and the function board(s)..
Utilizing the 915M30S LoRa module from EBYTE, which is a 1W (30dBm) transceiver based around the SX1276 from Semtech. There is a robust edge mount RP-SMA connector for large LoRa (915MHz) antennas.
with modification, a U.FL connector is also available. We've successfully tested a 12 miles line-of-sight transmission with this module (user results may vary)..
Board Features: M.2 MicroMod Edge Interface, Keyed Screw Slots, RP-SMA Antenna Connector, Configurable U.FL Antenna Connector. MicroMod Peripherals Used: 5V Power.
1W 915M30S LoRa Module Features: Based on SX1276 chipset from Semtech.
modulation: LoRa, FSK, GFSK, MSK, GMSK, OOK.
Data Rate: FSK: 1.2 - 300kbps, LoRa: 0.018 - 37.5kbps.
Note: A MicroMod Processor, Main Board, and antenna are not included with this MicroMod LoRa Function Board. These parts will need to be purchased separately.

2 in 1 lipo battery parallel charging board lipo charger,supporting XT60 connector and XT30 conector lipo battery.It is just a parallel charging board, not a diret charger, need to connect with a charger which support the balance port ( JST connector).
Thicken PCB copper foil, allow security using 35A charging current..
This lipo balance charging board supports up to four packs of the same type, same cells 2S-6S lipo battery pack,such as 2S lipo battery,3S lipo battery ,4S lipo battery,5S lipo battery,6S lipo battery..
Equipped with 40A fuse between any two groups of batteries, to prevent line burned due to the large battery pressure.
Output Connector:XT30 connector /XT60 connector,support xt30 and xt60 lipo batteries..

Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
Additional Features: 1mAh battery backup for RTC. Buttons: Reset, Boot, LEDs. Power. 3.3V. Phillips #0 M2.5x3mm screw included.
Carrier board only. MicroMod processor board will be needed to use..

Male Adapter with PCB: It can connect circuit board or weld line with PCB board.The shell is easily four inches long, plus a spring strain relief. you....
The soldier pads inside the shell do not have all the pins broken out, but you can just solder to the pin connections directly for odd pin outs. Note....
Used to build a breakout box:Lots of cars do not have 16 pin connector,such as some old cars. However now lots of diagnose tool is 16 pin connector,so....
Notice:It is just a small connector,do not have any accessory or software.Has a circuit board you could tack connections..
Package Include:Standard 16Pin Male Plug x 1.

This protection board is suitable for 3 series 3.7V 18650 li-ion cell..
The protection board is for cell Li-ion batteries, it can be used for ternary batteries, manganese acid batteries and cobalt acid batteries..
Support overcharge protection,overdischarge protection,overcurrent protection and short circuit protection..
This protection board is suitable for 3 series 3.7V 18650 Li-ion cell.Charging connector and discharging connector are separated..
Stable charging and discharging the various protection features such as precise overcharge protection,overdischarge protection,overcurrent protection....

[Specification]: 20 Pin to 20Pin 1.0mm Pitch for 20 Pin FFC Cable.
[Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
[Type]:This is 1.0mm pitch FPC connector extend adapter for make longer install..
[Package]:1 x Pin to Pin 1.0mm Pitch FPC Connector Extend Adapter.
[Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..

[Specification]: 20 Pin to 20 Pin 0.5mm Pitch for 20 Pin FFC Cable.
[Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
[Type]:This is 0.5mm pitch FPC connector extend adapter for make longer install..
[Package]:1 x Pin to Pin 0.5mm Pitch FPC Connector Extend Adapter.
[Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..

[Specification]: 20 Pin to 20 Pin 0.5mm Pitch for 20 Pin FFC Cable.
[Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
[Type]:This is 0.5mm pitch FPC connector extend adapter for make longer install..
[Package]:1 x Pin to Pin 0.5mm Pitch FPC Connector Extend Adapter.
[Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..

4245 PSOC and 2-channel motor ports programmable using Qwiic library. On board ATTINY84A supports up to two DC motor encoders. PWM control for up to four servos..
5v pass-through from RPi. Uninhibited access to the RPi camera connector & display connector. USB-C for powering 5V rail (Motors/Servos/backpowering Pi).
On board ICM-20948 9DOF IMU for motion sensing accessible via Qwiic library.
Qwiic connector for expansion to full SparkFun Qwiic ecosystem. External power inputs broken out to PTH headers. Designed for stacking, full header support & can use additional pHATs on top of it.
Raspberry Pi or other Single-board computer not included..