Best B45ac Relay

Solid State Relay SSR-40AA 40A AC to AC Input 80-250V AC and Output 24-380V AC (SSR-40 AA)

Shipping list: AC 220V vibration sensor delay module, with ultra-high sensitivity vibration sensor..
AC 220V power supply ultra-high sensitivity vibration delay module plus relay module plus delay three-in-one module, vibration switch module Alarm trigger, with 1 vibration sensor. Relay does not have B1 normally closed end..
corridor delay switch, delay energy-saving products.
Supply voltage: AC 220V power supply, Current: greater than 100mA.

This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).

1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
Standard interface can be directly connected with microcontrollers..
Red working status indicator for power on indication.Green working status indicator for relay the switch..
It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..

This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

Normally Open Interfaces Maximum Load : AC 250V/10A, DC 30V/10A.
2 Channel Relay Module 5V Comes with High-Current Relay,Trigger Current : 5mA.
5V Relay Module is 2 Channel Isolated, Each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
Relay Module Designed With Fault-Tolerant , Even If The Control Line Breaks, The Relay Will Not Move.
With Optical Coupling Isolation,Triggering More Reliable and Stable.
2 Channel Module Equipped With Screwed Terminal Plate and Fixed Bolt Holes,Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.