Best Arduino Mega 256motor Shield

REXQualis Most Complete Starter Kit Base on Arduino MEGA 2560 w/Detailed Tutorial Compatible with Arduino IDE

REXQualis complete starter kit base on Arduino MEGA 2560 comes with more than 200pcs components, 67 kinds of components and sensors module..
LCD1602 Module，MPU-6050 Module and RC522 RFID Module come with pin header, Motors come with wires, not need to solder by yourself..
Include High Quality Base Board base on Arduino MEGA 2560 100% compatible with Arduino IED..
Free PDF Tutorial and Datasheet are available to download from our official website or you can contact our customer service..
All of the Components and Integrated Circuits are individually packaged and labeled, and packing in a plastic box which is bigger enough for you..

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

The 3.2 tft lcd expansion board is compatible with arduino mega 2560.
With tft lcd shield, you can use 3.2 touch screen with mega more conveniently.
This 3.2" lcd shield is NOT compatible with all 3.2" tft lcd. Please chheck it carefully..
You can buy 3.2" tft lcd for the shield by "Visit the DIYmalls Store".
If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question"..

Advancing the development of robotics technology w/ Earth's 2nd biggest & most advanced starter kit for Arduino. 65+ pieces w/ FIVE main boards: 100% Arduino-compatible Uno R3, Mega 2560, Nano V3, ESP32 WiFi+Bluetooth and ESP8266 NodeMCU development platforms.
Explore programming electronics with all of the most common sensors and modules in Arduino like RFID Card-Key Reader, Ultrasonic Sensor, Real Time Clock, Impact Switch, 3-Axis Accelerometer, LCD, Relay, Servo and Stepper Motor - suitable for beginner or advanced users.
Build wireless IoT Automation projects with ESP32 Development Board, HC-05 Bluetooth Module, ESP8266 Wi-Fi Module, 2x NRF24L01 Wireless Transceivers and the W5100 Ethernet Shield.
All-in-one bundle with extra accessories + 16G USB storage with free access to the GAR Dropbox Cloud including PDF guides & links to tutorials and videos to help you learn to program all the parts and get started quickly.
Effective technical/customer support from USA with lifetime replacement guarantee on all parts – The Monster comes in 16" x 12" durable orga....

Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
! ! ! Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact us..

Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact US..

Made of high quality materials. Lightweight and easy to carry..
Designed with spring clips for easy battery installation and removal..
EASY TO INSTALL AND SAVE WORK: The cable comes with a 9V battery holder and 3 screw fixing holes on the base for easy fixation.
With this snap cable you can save yourself the work of soldering the battery snap to the DC coax plug.
Widely used in Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, Development Boards, Evaluation Boards, Breadboards, Arduino DIY,....

This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip..
Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel..
Tested compatible for Arduino Mega, Diecimila & Duemilanove..
2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter..
Multi-function, easy to operate, a strong driver library support and feature updates..

R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory..
R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). Comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files)..
This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..