Best Arduino Battery Connector

4xAA Battery Pack Holder Case Box to DC Barrel Jack Connector Compatible with Arduino(Pack of 2)

The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector.
The connector compatible with Arduino (among a number of other products) allowing you to easily make your project battery powered.

6600 MAH CAPACITY- 3.7V battery- Provide power for Raspberry Pi and Arduino systems, as well as many other products.
BUILT-IN OVER/UNDER CURRENT PROTECTION CIRCUIT- Automatic protection from low voltage drain or overcharging damage (2.75V cut-off).
10cm (3.9 INCH) BATTERY CONNECTOR CABLE- Provides placement flexibility, along with a genuine JST 2-Pin connector.
DIMENSIONS and WEIGHT- 65mm L x 54mm H x 18mm D, 150g = 2.55 inch L x 2.125 inch H x 0.70 inch D, 5.29 oz.

Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
! ! ! Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact us..

Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact US..

For Arduino kits and Affordable Price - This is a complete Kit with more than 200pcs components for adults, students and beginners.. Includes 2560 controller board and USB cable, 100% compatible with Arduino Mega 2560 R3 Mega328 Nano for Arduino kit..
Detailed Instructions - This 2560 Kit with detailed pdf tutorial in the CD, you can learn to code and program faster and easier with all the components..
25 Projects Provided - As an upgraded starter kit compatible with arduino 2560 controller board, more than 20 interesting lessons are included. Allowing for a dynamic creative learning experience..
Compatible with Arduino- R3 board compatible with Arduino,use ATMEGA16U2 chip, Faster transfer rates and more memory..
Control using r3 ATmega328P chip, Includes new pin configuration (SCL, SDA, IOREF) Clearly print on the female header connector, more precise and easier to use the wire..

for ARDUINO COMPATIBLE - Use the Nano-C with the for Arduino development IDE on your PC, Mac or Linux computer (USB driver installation required on some OSes).
PERFECT FOR BEGINNER OR EXPERT - Learn electronics and programming or jump start your latest project. Get started with the Nano-C in just minutes.
The Nano-C is breadboard-friendly and can be powered by USB, regulated 5V supply or unregulated 7-12V source. Connectors shipped unsoldered to fit the smallest of spaces.
Nano C for Arduino | USB Type-C Connector | ATmega328P | 5V | 16MHz | Without Cable | Connectors Unsoldered.
Uses the latest USB Type-C connector for compatibility with modern laptop and desktop computers. The Type-C connector is fully reversible which makes connecting a breeze.

The AA Battery Holder suit for 4x 1.5V AA batteries, and ouput voltage is 6 volt..
I Type Battery Snap Connector with hard plastic shell, 15 cm / 6 inch length, easy to solder or connect..
Made of thicken plastic shell, copper conductor and nickel-plated steel spring, to ensure effective good contact, sturdy and durable..
4 AA Battery Case Size is 57 * 32 * 29mm, widely used in electronic circuit experiment, Arduino projects, led devices, household appliances etc..
Package includes 2pcs 4x AA Battery Holder, 2pcs I Type Battery Snap Wire Leads..

The AA Battery Holder suit for 8x 1.5V AA batteries, and ouput voltage is 12 volt..
I Type Battery Snap Connector with hard plastic shell, 15 cm / 6 inch length, easy to solder or connect..
Made of thicken plastic shell, copper conductor and nickel-plated steel spring, to ensure effective good contact, sturdy and durable..
8 AA Battery Case Size is 63 * 58 * 30mm, widely used in electronic circuit experiment, Arduino projects, led devices, household appliances etc..
Package includes 2pcs 8x AA Battery Holder, 2pcs I Type Battery Snap Wire Leads..

Made of high quality materials. Lightweight and easy to carry..
Designed with spring clips for easy battery installation and removal..
EASY TO INSTALL AND SAVE WORK: The cable comes with a 9V battery holder and 3 screw fixing holes on the base for easy fixation.
With this snap cable you can save yourself the work of soldering the battery snap to the DC coax plug.
Widely used in Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, Development Boards, Evaluation Boards, Breadboards, Arduino DIY,....