Best 5v Motors

Drone Follows Me Everywhere

... Long Flight Time】: Come with 2 intelligent batteries which support up to 50 minutes flight in total. Please charge the battery with 5V/3A or 5V/2A wall charger. It takes about 6.5 hours to fully charge the battery..
【Level 6 Wind Resistance】: The low noise brushless motors plus the level 6 wind resistance provide you a quieter and stable flight experience. Its ability to hover in one spot without worrying about it moving around makes filming simple and enjoyable as you watch on your phone..
【9800ft Video Transmission】: The F7GB2 drone has extended video transmission range up to 3km/9800ft, providing you crisp images and smooth video..
【Safe to Fly and Back】: F7 drone will return to home automatically when the signal is lost, low battery or the Return to Home is pressed. Don't have to worry about losing your drone..

TB6612 motor driver with 1.2A per channel.
2 full H-bridges means you can drive 2-4 solenoids (only two can be active), two DC motors bi-directionally, or one stepper motor..
Runs at 2.7V-5V logic. The motor & logic voltage are separate..
Good for motor voltages from 4.5V up to 13.5V.

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO).
Integrates 5V regulator, allows providing power to Raspberry Pi.
6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable motor drive current via potentiometer, maximum 2.5A current output.
Onboard dual DRV8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use.
Onboard multi connector options for stepper motors in different specifications.

Waterproof DesignThe RC water pump is waterproof and works well in water, JR plug suitable for plug into the receiver, plug and play..
Long Working TimeUnder the condition of 5V voltage, the pump works continuously for 15 hours and pumps water continuously..
Application forPut it to work normally, the temperature will be hot, but it belongs to the normal range and will not affect the use, suitable for RC aircraft carriers, warships, battleships, etc. on a series of remotecontrolled ships that require water cooling for motors and ESCs..
Stable PerformanceThe power supply method is not to take power from the receiver, the battery used is greater than 2S and the voltage is between 728V, which is need to use a stepdown module to make the operation more stable..
Special NoteThe RC water pump is suitable for installation on remote control boats that require water cooling with watercooled motors and without waterabsorbing steering gear..

Super smooth, accurate and programmable throttle linearity and throttle response..
Over temperature protection ,low voltage cut off protection ,signal loss protection and so on..
Strong BEC output 2A/5V continuous and peak to 3A..
Supporting high RPM motors and programmable by programming card and transmitter ..
High efficiency with low resistance and low heat MOSFET and CPU.

4245 PSOC and 2-channel motor ports programmable using Qwiic library. On board ATTINY84A supports up to two DC motor encoders. PWM control for up to four servos..
5v pass-through from RPi. Uninhibited access to the RPi camera connector & display connector. USB-C for powering 5V rail (Motors/Servos/backpowering Pi).
On board ICM-20948 9DOF IMU for motion sensing accessible via Qwiic library.
Qwiic connector for expansion to full SparkFun Qwiic ecosystem. External power inputs broken out to PTH headers. Designed for stacking, full header support & can use additional pHATs on top of it.
Raspberry Pi or other Single-board computer not included..